Turn Your Forklift
into an
Aerial Work Platform
Aerial Work Platform
- Expanded Metal Deck
- Spring Loaded Gate Latch
- Larger 1½" sq. tube Guard Rails
- Larger 1" dia. Fork Retaining Pins w/ pin storage
- End Fork Loops for easier handling of platform
- Integral 5½" high Toe Boards
- Spring Loaded Gate Latch
- Larger 1½" sq. tube Guard Rails
- Larger 1" dia. Fork Retaining Pins w/ pin storage
- End Fork Loops for easier handling of platform
- Integral 5½" high Toe Boards
- ▶ Goes where scissor-lifts can't
- ▶ Faster than scaffold
- ▶ Provides a wider platform than boom lifts
- ▶ Reaches over obstructions
- ▶ Simple and Inexpensive
Quick-Tach & Slip-on-Forks
Models Available
Models Available
rev_Page_2.jpg)
- Full Perimeter Guard Rail System constructed of 1½" square steel tubing & consisting of a 42" high top rail, a mid rail, and 5½" high toeboards. Access gates with spring pin latches are provided at each end. Entire Guard Rail System can be easily removed and laid flat inside platform for transportation.
- Deck consists of a strong but lightweight engineered steel frame with expanded metal deck.
- The “Universal Fit” Slip-On-the-Forks design can be used with both Extendible Reach and Straight Mast forklifts. Forks slide into steel fork pockets and are secured with two heavy duty steel pins behind the heel of the forks. They are designed for use with a 48" or wider carriage and 48" long forks up to 7" wide and 2¾" thick. Forks longer than 48" can be used, however, they will extend out past the front of the platform.
- The Quick-Tach models are built to fit specific makes & models of forklifts that are equipped with a quick-tach. The forks and carriage are removed and the Platform attaches to the boom.
- All Models are rated at 1,000 lbs. load capacity. Rating applies to platform only and does not reflect capacity of forklift.
- Optional Mast Protection Screen (Model 1250)
protects personnel from moving parts of forklift mast.
Constructed of square steel tubing and expanded
metal, the screen measures
42" wide x 84" tall. It
attaches
to the back guardrail with
u-bolts. A mast protection
screen should be used with
all straight mast forklifts and
with any others where a mast
poses a safety hazard.
| UNIVERSAL FIT "Slip-on-Forks" MODELS | ||
| Model | Size | Weight |
| 1204B | 4' x 4' | 310 lbs. |
| 1206B | 4' x 6' | 380 lbs. |
| 1208B | 4' x 8' | 425 lbs. |
| 1210B | 4' x 9' 8" | 505 lbs. |
| "QUICK-TACH" MODELS | ||
| Model | Size | Weight |
| 1204BQT | 4' x 4' | ±460 lbs. |
| 1206BQT | 4' x 6' | ±530 lbs. |
| 1208BQT | 4' x 8' | ±575 lbs. |
| 1210BQT | 4' x 9' 8" | ±635 lbs. |
| Specify forklift make & model when ordering QT platforms. | ||
SPECIAL SAFETY NOTE:
I.T.S.D.F. Standard B56.6 for Rough Terrain Forklift Trucks states that ... the platform floor dimension shall not exceed the overall width of the truck (measured across the load bearing tires) plus 10" on either side. Star Industries recommends that all users of Star Safety Work Platforms conform to this requirement as well as the other requirements of B56.6. Furthermore, users should conform to all applicable local, state, and federal safety standards.
Star Industries recommends you contact the respective forklift manufacturer for any additional safety requirements or limitations.
I.T.S.D.F. Standard B56.6 for Rough Terrain Forklift Trucks states that ... the platform floor dimension shall not exceed the overall width of the truck (measured across the load bearing tires) plus 10" on either side. Star Industries recommends that all users of Star Safety Work Platforms conform to this requirement as well as the other requirements of B56.6. Furthermore, users should conform to all applicable local, state, and federal safety standards.
Star Industries recommends you contact the respective forklift manufacturer for any additional safety requirements or limitations.
